Nonstop flight route between Bainbridge, Georgia, United States and Coatesville, Pennsylvania, United States:
Departure Airport:
Arrival Airport:
Distance from BGE to CTH:
Share this route:
Jump to:
- About this route
- BGE Airport Information
- CTH Airport Information
- Facts about BGE
- Facts about CTH
- Map of Nearest Airports to BGE
- List of Nearest Airports to BGE
- Map of Furthest Airports from BGE
- List of Furthest Airports from BGE
- Map of Nearest Airports to CTH
- List of Nearest Airports to CTH
- Map of Furthest Airports from CTH
- List of Furthest Airports from CTH
About this route:
A direct, nonstop flight between Decatur County Industrial Air Park (BGE), Bainbridge, Georgia, United States and Chester County G. O. Carlson Airport (CTH), Coatesville, Pennsylvania, United States would travel a Great Circle distance of 793 miles (or 1,277 kilometers).
A Great Circle is the shortest distance between 2 points on a sphere. Because most world maps are flat (but the Earth is round), the route of the shortest distance between 2 points on the Earth will often appear curved when viewed on a flat map, especially for long distances. If you were to simply draw a straight line on a flat map and measure a very long distance, it would likely be much further than if you were to lay a string between those two points on a globe. Because of the relatively short distance between Decatur County Industrial Air Park and Chester County G. O. Carlson Airport, the route shown on this map most likely still appears to be a straight line.
Departure Airport Information:
IATA / ICAO Codes: | BGE / KBGE |
Airport Name: | Decatur County Industrial Air Park |
Location: | Bainbridge, Georgia, United States |
GPS Coordinates: | 30°58'18"N by 84°38'15"W |
Area Served: | Decatur County |
Operator/Owner: | Decatur County |
Airport Type: | Public |
Elevation: | 141 feet (43 meters) |
# of Runways: | 2 |
View all routes: | Routes from BGE |
More Information: | BGE Maps & Info |
Arrival Airport Information:
IATA / ICAO Codes: | CTH / KMQS |
Airport Names: |
|
Location: | Coatesville, Pennsylvania, United States |
GPS Coordinates: | 39°58'44"N by 75°51'56"W |
Operator/Owner: | Chester County Area Airport Authority |
Airport Type: | Public |
Elevation: | 660 feet (201 meters) |
# of Runways: | 1 |
View all routes: | Routes from CTH |
More Information: | CTH Maps & Info |
Facts about Decatur County Industrial Air Park (BGE):
- The closest airport to Decatur County Industrial Air Park (BGE) is Tallahassee Regional Airport (TLH), which is located 43 miles (70 kilometers) SSE of BGE.
- Decatur County Industrial Air Park (BGE) has 2 runways.
- Following entry of the United States into World War II, the Chief of the Army Air Corps directed the Air Corps Flying Training Command Southeast Training Center to immediately take action to select air base sites needed to increase its pilot training rate to meet anticipated wartime demands.
- A level area near Bainbridge, seven miles northwest of the City adjacent to the Seaboard Air Line Railroad was selected by the Air Corps, and the City of Bainbridge and Decatur County purchased 2,070 acres for $66,800 and then leased the property to the Army for $1 per annum for a basic flight training base authorizing 89.9 million for its construction.
- Because of Decatur County Industrial Air Park's relatively low elevation of 141 feet, planes can take off or land at Decatur County Industrial Air Park at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
- During World War II, the airfield conducted flight training of new pilots by Army Air Forces Flying Training Command.
- Through the years a lot of material has been gathered about the Southern Airways School and Bainbridge Air Base.
- There was little need, however, for the airfield, and in the immediate postwar years, farmers leased the open areas of the airfield for cultivation and the cantonment area was used for various purposes.
- The furthest airport from Decatur County Industrial Air Park (BGE) is Kalbarri Airport (KAX), which is located 11,278 miles (18,150 kilometers) away in Kalbarri, Western Australia, Australia.
Facts about Chester County G. O. Carlson Airport (CTH):
- The airport covers 250 acres.
- Chester County G. O. Carlson Airport (CTH) currently has only 1 runway.
- The furthest airport from Chester County G. O. Carlson Airport (CTH) is Margaret River Airport (MGV), which is located 11,702 miles (18,833 kilometers) away in Margaret River, Western Australia, Australia.
- In addition to being known as "Chester County G. O. Carlson Airport", another name for CTH is "MQS".
- Chester County's airport identifier was 40N but it has recently changed to MQS.
- The closest airport to Chester County G. O. Carlson Airport (CTH) is Brandywine Airport (OQN), which is located only 15 miles (24 kilometers) E of CTH.
- Because of Chester County G. O. Carlson Airport's relatively low elevation of 660 feet, planes can take off or land at Chester County G. O. Carlson Airport at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.