Nonstop flight route between Rensselaer, Indiana, United States and Coconut Island (Poruma Island), Queensland, Australia:
Departure Airport:
Arrival Airport:
Distance from RNZ to CNC:
Share this route:
Jump to:
- About this route
- RNZ Airport Information
- CNC Airport Information
- Facts about RNZ
- Facts about CNC
- Map of Nearest Airports to RNZ
- List of Nearest Airports to RNZ
- Map of Furthest Airports from RNZ
- List of Furthest Airports from RNZ
- Map of Nearest Airports to CNC
- List of Nearest Airports to CNC
- Map of Furthest Airports from CNC
- List of Furthest Airports from CNC
About this route:
A direct, nonstop flight between Jasper County Airport (RNZ), Rensselaer, Indiana, United States and Coconut Island (CNC), Coconut Island (Poruma Island), Queensland, Australia would travel a Great Circle distance of 8,716 miles (or 14,027 kilometers).
A Great Circle is the shortest distance between 2 points on a sphere. Because most world maps are flat (but the Earth is round), the route of the shortest distance between 2 points on the Earth will often appear curved when viewed on a flat map, especially for long distances. If you were to simply draw a straight line on a flat map and measure a very long distance, it would likely be much further than if you were to lay a string between those two points on a globe. Because of the large distance between Jasper County Airport and Coconut Island, the route shown on this map most likely appears curved because of this reason.
Try it at home! Get a globe and tightly lay a string between Jasper County Airport and Coconut Island. You'll see that it will travel the same route of the red line on this map!
Departure Airport Information:
IATA / ICAO Codes: | RNZ / KRZL |
Airport Names: |
|
Location: | Rensselaer, Indiana, United States |
GPS Coordinates: | 40°56'52"N by 87°10'57"W |
Area Served: | Jasper County |
Operator/Owner: | Jasper County Board of Aviation Commissioners |
Airport Type: | Public |
Elevation: | 698 feet (213 meters) |
# of Runways: | 2 |
View all routes: | Routes from RNZ |
More Information: | RNZ Maps & Info |
Arrival Airport Information:
IATA / ICAO Codes: | CNC / YCCT |
Airport Name: | Coconut Island |
Location: | Coconut Island (Poruma Island), Queensland, Australia |
GPS Coordinates: | 10°3'0"S by 143°4'1"E |
Operator/Owner: | Torres Strait Island Regional Council |
Airport Type: | Private |
Elevation: | 10 feet (3 meters) |
# of Runways: | 1 |
View all routes: | Routes from CNC |
More Information: | CNC Maps & Info |
Facts about Jasper County Airport (RNZ):
- Because of Jasper County Airport's relatively low elevation of 698 feet, planes can take off or land at Jasper County Airport at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
- The furthest airport from Jasper County Airport (RNZ) is Margaret River Airport (MGV), which is located 11,126 miles (17,906 kilometers) away in Margaret River, Western Australia, Australia.
- The closest airport to Jasper County Airport (RNZ) is Kentland Municipal Airport (KKT), which is located only 18 miles (29 kilometers) SW of RNZ.
- In addition to being known as "Jasper County Airport", another name for RNZ is "RZL".
- Jasper County Airport covers an area of 108 acres at an elevation of 698 feet above mean sea level.
- Jasper County Airport (RNZ) has 2 runways.
Facts about Coconut Island (CNC):
- Coconut Island (CNC) currently has only 1 runway.
- The furthest airport from Coconut Island (CNC) is São Filipe Airport (SFL), which is located 11,533 miles (18,561 kilometers) away in Fogo, Cape Verde.
- Because of Coconut Island's relatively low elevation of 10 feet, planes can take off or land at Coconut Island at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
- The closest airport to Coconut Island (CNC) is Yam Island Airport (XMY), which is located 23 miles (37 kilometers) WNW of CNC.