Nonstop flight route between Columbus, Mississippi, United States and Melfa, Virginia, United States:
Departure Airport:
Arrival Airport:
Distance from CBM to MFV:
Share this route:
Jump to:
- About this route
- CBM Airport Information
- MFV Airport Information
- Facts about CBM
- Facts about MFV
- Map of Nearest Airports to CBM
- List of Nearest Airports to CBM
- Map of Furthest Airports from CBM
- List of Furthest Airports from CBM
- Map of Nearest Airports to MFV
- List of Nearest Airports to MFV
- Map of Furthest Airports from MFV
- List of Furthest Airports from MFV
About this route:
A direct, nonstop flight between Columbus Air Force Base (CBM), Columbus, Mississippi, United States and Accomack County Airport (MFV), Melfa, Virginia, United States would travel a Great Circle distance of 763 miles (or 1,228 kilometers).
A Great Circle is the shortest distance between 2 points on a sphere. Because most world maps are flat (but the Earth is round), the route of the shortest distance between 2 points on the Earth will often appear curved when viewed on a flat map, especially for long distances. If you were to simply draw a straight line on a flat map and measure a very long distance, it would likely be much further than if you were to lay a string between those two points on a globe. Because of the relatively short distance between Columbus Air Force Base and Accomack County Airport, the route shown on this map most likely still appears to be a straight line.
Departure Airport Information:
| IATA / ICAO Codes: | CBM / KCBM |
| Airport Names: |
|
| Location: | Columbus, Mississippi, United States |
| GPS Coordinates: | 33°38'38"N by 88°26'38"W |
| View all routes: | Routes from CBM |
| More Information: | CBM Maps & Info |
Arrival Airport Information:
| IATA / ICAO Codes: | MFV / KMFV |
| Airport Name: | Accomack County Airport |
| Location: | Melfa, Virginia, United States |
| GPS Coordinates: | 37°38'48"N by 75°45'38"W |
| Operator/Owner: | Accomack County Airport Commission |
| Airport Type: | Public |
| Elevation: | 47 feet (14 meters) |
| # of Runways: | 1 |
| View all routes: | Routes from MFV |
| More Information: | MFV Maps & Info |
Facts about Columbus Air Force Base (CBM):
- In preparation for this transfer, Air Training Command had activated the 3650th Pilot Training Wing at Columbus on 15 February.
- In addition to being known as "Columbus Air Force Base", another name for CBM is "Columbus AFB".
- When the war ended in 1945, the base strength had reached a peak of 2,300 enlisted men, 300 officers, and an average of 250 pilot cadets per class.
- But while the Air Force’s pilot training requirements were decreasing, its strategic air arm was expanding.During the 1950s, Strategic Air Command wings had become extremely large.
- The closest airport to Columbus Air Force Base (CBM) is Columbus-Lowndes County Airport (UBS), which is located only 13 miles (21 kilometers) SSE of CBM.
- No one designated or suggested a name for the new base until 22 January 1942.
- The furthest airport from Columbus Air Force Base (CBM) is Margaret River Airport (MGV), which is located 11,088 miles (17,844 kilometers) away in Margaret River, Western Australia, Australia.
Facts about Accomack County Airport (MFV):
- The closest airport to Accomack County Airport (MFV) is Wallops Flight Facility Airport (WAL), which is located 26 miles (42 kilometers) NE of MFV.
- Because of Accomack County Airport's relatively low elevation of 47 feet, planes can take off or land at Accomack County Airport at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
- The furthest airport from Accomack County Airport (MFV) is Margaret River Airport (MGV), which is located 11,777 miles (18,953 kilometers) away in Margaret River, Western Australia, Australia.
- Accomack County Airport (MFV) currently has only 1 runway.
- Accomack County Airport covers an area of 100 acres which contains one runway designated 3/21 with a 5,000 x 100 ft asphalt surface.
