Nonstop flight route between Tampa, Florida, United States and Dammam, Saudi Arabia:

About this route:

A direct, nonstop flight between MacDill Air Force Base (MCF), Tampa, Florida, United States and King Fahd International Airport (DMM), Dammam, Saudi Arabia would travel a Great Circle distance of 7,527 miles (or 12,114 kilometers).

A Great Circle is the shortest distance between 2 points on a sphere. Because most world maps are flat (but the Earth is round), the route of the shortest distance between 2 points on the Earth will often appear curved when viewed on a flat map, especially for long distances. If you were to simply draw a straight line on a flat map and measure a very long distance, it would likely be much further than if you were to lay a string between those two points on a globe. Because of the large distance between MacDill Air Force Base and King Fahd International Airport, the route shown on this map most likely appears curved because of this reason.

Try it at home! Get a globe and tightly lay a string between MacDill Air Force Base and King Fahd International Airport. You'll see that it will travel the same route of the red line on this map!

Departure Airport Information:

Arrival Airport Information:

Facts about MacDill Air Force Base (MCF):

• In addition MacDill provided transitional training in the B-17 Flying Fortress.
• With the United States entry into World War II, the primary mission of MacDill Field became the training of bombardment units under III Bomber Command.
• With the end of hostilities in September 1945 the training B-29 aircrew training program began to slow down.
• The furthest airport from MacDill Air Force Base (MCF) is Shark Bay Airport (MJK), which is located 11,436 miles (18,405 kilometers) away in Monkey Mia, Western Australia, Australia.
• All of these airfields came under the jurisdiction of Third Air Force.
• In addition to being known as "MacDill Air Force Base", another name for MCF is "MacDill AFB".
• MacDill has a total of 38 tenant units according to the official MacDill website."MacDill Air Force Base Units".
• The closest airport to MacDill Air Force Base (MCF) is Peter O. Knight Airport (TPF), which is located only 6 miles (10 kilometers) NE of MCF.

Facts about King Fahd International Airport (DMM):

• Because of King Fahd International Airport's relatively low elevation of 72 feet, planes can take off or land at King Fahd International Airport at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
• The airport is classified as Code E by ICAO which makes it designed to accommodate large aircraft such as Boeing 747-400 and A340-600.
• The airport has two parallel runways with a length of 4,000 m each, in addition to taxiways parallel to the runways and a cross taxiway to connect the two runways.
• A road for ground support equipment runs along the western side of the central terminal.
• Design started in 1976.
• The Royal Terminal is reserved for the Saudi Royal Family, government personnel, and official guests.
• In addition to being known as "King Fahd International Airport", other names for DMM include "Dammam Airport" and "مطار الملك فهد الدولي".
• King Fahd International Airport (DMM) has 2 runways.
• The furthest airport from King Fahd International Airport (DMM) is Totegegie Airport (GMR), which is nearly antipodal to King Fahd International Airport (meaning King Fahd International Airport is almost on the exact opposite side of the Earth from Totegegie Airport), and is located 12,061 miles (19,411 kilometers) away in Mangareva, Gambier Islands, French Polynesia.
• Several sources, such as the Guinness World Record mention this airport as the largest in the world, with 780 square kilometers.
• King Fahd International Airport handled 7,000,000 passengers last year.
• The closest airport to King Fahd International Airport (DMM) is King Abdulaziz Air Base (DHA), which is located 26 miles (42 kilometers) ESE of DMM.
• The terminal's design allows for transforming the operation system to a fully automatic system equipped with multi-level racks and a container stacking system.