Nonstop flight route between Cortland, New York, United States and Keene, New Hampshire, United States:
Departure Airport:
Arrival Airport:
Distance from CTX to EEN:
Share this route:
Jump to:
- About this route
- CTX Airport Information
- EEN Airport Information
- Facts about CTX
- Facts about EEN
- Map of Nearest Airports to CTX
- List of Nearest Airports to CTX
- Map of Furthest Airports from CTX
- List of Furthest Airports from CTX
- Map of Nearest Airports to EEN
- List of Nearest Airports to EEN
- Map of Furthest Airports from EEN
- List of Furthest Airports from EEN
About this route:
A direct, nonstop flight between Cortland County Airport (CTX), Cortland, New York, United States and Dillant–Hopkins Airport (EEN), Keene, New Hampshire, United States would travel a Great Circle distance of 201 miles (or 324 kilometers).
A Great Circle is the shortest distance between 2 points on a sphere. Because most world maps are flat (but the Earth is round), the route of the shortest distance between 2 points on the Earth will often appear curved when viewed on a flat map, especially for long distances. If you were to simply draw a straight line on a flat map and measure a very long distance, it would likely be much further than if you were to lay a string between those two points on a globe. Because of the relatively short distance between Cortland County Airport and Dillant–Hopkins Airport, the route shown on this map most likely still appears to be a straight line.
Departure Airport Information:
IATA / ICAO Codes: | CTX / |
Airport Names: |
|
Location: | Cortland, New York, United States |
GPS Coordinates: | 42°35'33"N by 76°12'52"W |
Area Served: | Cortland |
Operator/Owner: | Cortland County |
Airport Type: | Public |
Elevation: | 1198 feet (365 meters) |
# of Runways: | 1 |
View all routes: | Routes from CTX |
More Information: | CTX Maps & Info |
Arrival Airport Information:
IATA / ICAO Codes: | EEN / KEEN |
Airport Name: | Dillant–Hopkins Airport |
Location: | Keene, New Hampshire, United States |
GPS Coordinates: | 42°53'53"N by 72°16'14"W |
Operator/Owner: | Keene, New Hampshire |
Airport Type: | City of Keene |
Elevation: | 149 feet (45 meters) |
# of Runways: | 2 |
View all routes: | Routes from EEN |
More Information: | EEN Maps & Info |
Facts about Cortland County Airport (CTX):
- Cortland County Airport (CTX) currently has only 1 runway.
- The closest airport to Cortland County Airport (CTX) is Ithaca Tompkins Regional Airport (ITH), which is located only 14 miles (23 kilometers) WSW of CTX.
- The furthest airport from Cortland County Airport (CTX) is Margaret River Airport (MGV), which is located 11,581 miles (18,638 kilometers) away in Margaret River, Western Australia, Australia.
- In addition to being known as "Cortland County Airport", another name for CTX is "N03".
Facts about Dillant–Hopkins Airport (EEN):
- The furthest airport from Dillant–Hopkins Airport (EEN) is Margaret River Airport (MGV), which is located 11,700 miles (18,830 kilometers) away in Margaret River, Western Australia, Australia.
- Dillant–Hopkins Airport (EEN) has 2 runways.
- The closest airport to Dillant–Hopkins Airport (EEN) is Jaffrey Airport - Silver Ranch Airpark (AFN), which is located only 15 miles (24 kilometers) ESE of EEN.
- Because of Dillant–Hopkins Airport's relatively low elevation of 149 feet, planes can take off or land at Dillant–Hopkins Airport at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
- 1954 would see Northeast Airlines begin its air freight service out of the airport, six years after air freight service first began there.
- 1967 would also see Vice President Hubert H.
- The city had enjoyed six decades of regularly scheduled airline service since the 1940s with multiple daily flights operated with a mix of commuter, regional prop, and mainline jet service.
- In 1967 the FAA recommended a $1.8 million series of improvements which would include further extending the runways, the construction of a control tower, improved buildings, and other facilities.