Nonstop flight route between Cortland, New York, United States and Bainbridge, Georgia, United States:
Departure Airport:
Arrival Airport:
Distance from CTX to BGE:
Share this route:
Jump to:
- About this route
- CTX Airport Information
- BGE Airport Information
- Facts about CTX
- Facts about BGE
- Map of Nearest Airports to CTX
- List of Nearest Airports to CTX
- Map of Furthest Airports from CTX
- List of Furthest Airports from CTX
- Map of Nearest Airports to BGE
- List of Nearest Airports to BGE
- Map of Furthest Airports from BGE
- List of Furthest Airports from BGE
About this route:
A direct, nonstop flight between Cortland County Airport (CTX), Cortland, New York, United States and Decatur County Industrial Air Park (BGE), Bainbridge, Georgia, United States would travel a Great Circle distance of 927 miles (or 1,492 kilometers).
A Great Circle is the shortest distance between 2 points on a sphere. Because most world maps are flat (but the Earth is round), the route of the shortest distance between 2 points on the Earth will often appear curved when viewed on a flat map, especially for long distances. If you were to simply draw a straight line on a flat map and measure a very long distance, it would likely be much further than if you were to lay a string between those two points on a globe. Because of the relatively short distance between Cortland County Airport and Decatur County Industrial Air Park, the route shown on this map most likely still appears to be a straight line.
Departure Airport Information:
IATA / ICAO Codes: | CTX / |
Airport Names: |
|
Location: | Cortland, New York, United States |
GPS Coordinates: | 42°35'33"N by 76°12'52"W |
Area Served: | Cortland |
Operator/Owner: | Cortland County |
Airport Type: | Public |
Elevation: | 1198 feet (365 meters) |
# of Runways: | 1 |
View all routes: | Routes from CTX |
More Information: | CTX Maps & Info |
Arrival Airport Information:
IATA / ICAO Codes: | BGE / KBGE |
Airport Name: | Decatur County Industrial Air Park |
Location: | Bainbridge, Georgia, United States |
GPS Coordinates: | 30°58'18"N by 84°38'15"W |
Area Served: | Decatur County |
Operator/Owner: | Decatur County |
Airport Type: | Public |
Elevation: | 141 feet (43 meters) |
# of Runways: | 2 |
View all routes: | Routes from BGE |
More Information: | BGE Maps & Info |
Facts about Cortland County Airport (CTX):
- In addition to being known as "Cortland County Airport", another name for CTX is "N03".
- Cortland County Airport (CTX) currently has only 1 runway.
- The closest airport to Cortland County Airport (CTX) is Ithaca Tompkins Regional Airport (ITH), which is located only 14 miles (23 kilometers) WSW of CTX.
- The furthest airport from Cortland County Airport (CTX) is Margaret River Airport (MGV), which is located 11,581 miles (18,638 kilometers) away in Margaret River, Western Australia, Australia.
Facts about Decatur County Industrial Air Park (BGE):
- The furthest airport from Decatur County Industrial Air Park (BGE) is Kalbarri Airport (KAX), which is located 11,278 miles (18,150 kilometers) away in Kalbarri, Western Australia, Australia.
- Decatur County Industrial Air Park (BGE) has 2 runways.
- Because of Decatur County Industrial Air Park's relatively low elevation of 141 feet, planes can take off or land at Decatur County Industrial Air Park at a lower air speed than at airports located at a higher elevation. This is because the air density is higher closer to sea level than it would otherwise be at higher elevations.
- The contractor broke ground on 3 April 1942, for Bainbridge Army Airfield.
- Following entry of the United States into World War II, the Chief of the Army Air Corps directed the Air Corps Flying Training Command Southeast Training Center to immediately take action to select air base sites needed to increase its pilot training rate to meet anticipated wartime demands.
- The closest airport to Decatur County Industrial Air Park (BGE) is Tallahassee Regional Airport (TLH), which is located 43 miles (70 kilometers) SSE of BGE.
- Decatur County Industrial Air Park Airport covers an area of 940 acres at an elevation of 141 feet above mean sea level.
- During World War II, the airfield conducted flight training of new pilots by Army Air Forces Flying Training Command.
- There was little need, however, for the airfield, and in the immediate postwar years, farmers leased the open areas of the airfield for cultivation and the cantonment area was used for various purposes.